A pair of Legends and a pair of Copperheads for serious country tone.
- Legend 1058 10" Guitar Speaker
Voice Coil Diameter: 1.5", 38.1mm
Magnet Weight: 16 oz.
Power Rating.: 75W
Materials of Construction
Copper voice coil
Pressed steel basket
Paper cone edge
Solid composition felt dust cap
Eminence Crankin Country 10" Speaker Tone Kit
The affordable Eminence Crankin Country 10" Speaker Tone Kit features a pair of Eminence speakers including Legend 1058 10" Guitar Speakers and a pair of Eminence Copperhead Speakers. In an open- or closed-back setup, these speakers give you a nice balance of tone. They're perfect for country, but handle country, blues, bluegrass, and funk admirably too.
Eminence Legend 1058 10" Guitar Speaker
The Eminence Legend 1058 10" Guitar Speaker has a very meaty tone, but with sparkle, definition and a smooth top-end. Great for blues, country, and rock.
You get high power, vintage, seamed cone tonality for your guitar. They are ideal replacement speakers for trading out vintage alnico Jensen speakers.
2 Eminence Copperhead Speakers
These 10" Copperhead speakers provide an extremely balanced, vintage tone with a little country honk and a touch of classic blues. Perfect for country, blues, bluegrass, and funk. They're ideal for a 1, 2, or 4x10" open- or closed-back setup. They have 75W RMS handling, 150W peak and 8 ohm impedance.
Eminence recommends the Copperhead as a direct replacement speaker in the Fender G-DEC 30, Fender Princeton Recording Amp, and the Behringer V-tone GMX210 Combo Amplifier.
Order today with the no-risk assurance of our Total Satisfaction and Low Price Guarantees!
- Eminence Copperhead Speaker
75W RMS handling
8 ohm impedance
Legend 1058 10" Guitar Speaker
Nominal Basket Diameter: 10", 254mm
Nominal Impedance: 8 ohms
Power Rating*: 75W
Usable Frequency Range: 100Hz-6kHz
Magnet Weight: 16 oz.
Thiele & Small Parameters:
Resonant Frequency (fs): 97Hz
DC Resistance (Re): 7.49
Coil Inductance (Le): 0.56mH
Mechanical Q (Qms): 17.78
Electromagnetic Q (Qes): 1.21
Total Q (Qts): 1.13
Compliance Equivalent Volume (Vas): 26.4 liters / 0.9 cu. ft.
Peak Diaphragm Displacement Volume (Vd): 0cc
Mechanical Compliance of Suspension (Cms): 0.16mm/N
BL Product (BL): 8.0 T-M
Diaphragm Mass inc. Airload (Mms): 17 grams
Efficiency Bandwidth Product (EBP): 80
Maximum Linear Excursion (Xmax): 0.0mm
Surface Area of Cone (Sd): 344.9 cm2
Recommended Enclosure Volume:
Overall Diameter: 10.11", 256.8mm
Baffle Hole Diameter: 9.13", 231.8mm
Front Sealing Gasket: fitted as standard
Rear Sealing Gasket: fitted as standard
Mounting Holes Diameter: 0.23", 5.7mm
Mounting Holes B.C.D.: 9.6", 243.8mm
Depth: 4.1", 104mm
Net Weight: 4.4lb., 2kg
Shipping Weight: 5.4lb., 2.5kg
* Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, non-temperature controlled environment.
**The average output across the usable frequency range when applying 1W/1M into the nominal impedance. Ie: 2.83V/8ohms, 4V/16ohms.
Eminence response curves are measured under the following conditions: All speakers are tested at 1w/1m using a variety of test set-ups for the appropriate impedance " LMS using 0.25" supplied microphone (software calibrated) mounted 1m from wall/baffle " 2ft. x 2ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction " Hafler P1500 Trans-Nova amplifier " 2700 cu.ft. chamber with
fiberglass on all six surfaces (three with custom-made wedges)