Eminence Legend BP102 10" 200W Bass Speaker

The Eminence Legend BP102 10" Bass Speaker delivers rich bass tone with a lot of punch. Recommended for professional bass guitar applications in sealed or vented enclosures. The replacement speaker works well in single or multi-driver designs.

Use the Eminence Legend BP102 as a direct replacement speaker in the Ampeg SVT-810E, the Kustom Groove 4120, the Gallien-Krueger 4120 SBX, the Ashdown MAG 410T & MAG810T, and the Basson B410B speaker cabinets. Eminence recommends the Legend BP102 as a direct replacement in the Kustom Groove 310C, the Ampeg BA210SP, the Peavey Bam 210 combo amps.

Order today with the no-risk assurance of our Total Satisfaction and Low Price Guarantees!

• Nominal Basket Diameter: 10", 254mm
  Nominal Impedance*: 8 ohms
  Power Rating**: 200W
  Resonance: 35Hz
  Usable Frequency Range: 44Hz-4kHz
  Sensitivity***: 92
  Magnet Weight: 38 oz.
  Gap Height: 0.312", 7.92mm
  Voice Coil Diameter : 2", 50.8mm
  
  Resonant Frequency (fs): 35Hz
  DC Resistance (Re): 5.59
  Coil Inductance (Le): 0.83mH
  Mechanical Q (Qms): 5.36
  Electromagnetic Q (Qes): 0.47
  Total Q (Qts): 0.43
  Compliance Equivalent Volume (Vas): 91.2 liters / 3.2 cu. ft.
  Peak Diaphragm Displacement Volume (Vd): 207cc
  Mechanical Compliance of Suspension (Cms): 0.54mm/N
  BL Product (BL): 10.0 T-M
  Diaphragm Mass inc. Airload (Mms): 38 grams
  Efficiency Bandwidth Product (EBP): 75
  Maximum Linear Excursion (Xmax): 6.2mm
  Surface Area of Cone (Sd): 334.5 cm2
  Maximum Mechanical Limit (Xlim): 10.0mm
  
  Mounting Information
  Recommended Enclosure Volume
  Sealed: 14-28 liters/ 0.5-1 cu.ft.
  Vented: 25.5-62 liters/ 0.9-2.2 cu.ft.
  Overall Diameter: 10.08", 256.1mm
  Baffle Hole Diameter: 9.05", 229.7mm
  Front Sealing Gasket: fitted as standard
  Rear Sealing Gasket:
  Mounting Holes Diameter: 0.25", 6.4mm
  Mounting Holes B.C.D.: 9.66", 245.4mm
  Depth: 4.25", 108mm
  Net Weight: 8.9 lb., 4 kg
  Shipping Weight: 9.1 lbs., 4.1 kg
  
  Materials of Construction
  Copper voice coil
  Polyimide former
  Ferrite magnet
  Non-vented core
  Pressed steel basket
  Paper Cone
  Cloth cone edge
  Zurette dust cap
  
  
  *Please inquire about alternative impedances.
  **Multiple units exceed published rating evaluated under EIA 426A noise source and test standard while in a free-air, non-temperature controlled environment.
  ***The average output across the usable frequency range when applying 1W/1M into the nominal impedance. Ie: 2.83V/8ohms, 4V/16ohms.
  Eminence response curves are measured under the following conditions: All speakers are tested at 1w/1m using a variety of test set-ups for the appropriate impedance " LMS using 0.25" supplied microphone (software
  calibrated) mounted 1m from wall/baffle " 2ft. X 2ft. baffle is built into the wall with the speaker mounted flush against a steel ring for minimum diffraction " Hafler P1500 Trans-Nova amplifier " 2700 cu.ft. chamber with
  fiberglass on all six surfaces (three with custom-made wedges)