Item #1077117 Model #000-A3702-00010

Behringer EUROPOWER EP4000 Power Amplifier Standard

Sorry, this item is not available.

Powerful, road-tough unit for medium and larger gigs.

The Behringer EUROPOWER EP4000 is a professional-grade stereo power amplifier packing enough juice to rattle your bones. Designed for massive live sound reinforcement, its dual channels each pump out a thunderous 2,000W of peak power into 2-ohm loads—more than enough to drive full-size PA rigs to face-melting levels. With the Behringer EUROPOWER EP4000 amplifier, you get earth-shaking volume and pristine sonic precision.

Massive 2,000W Peak Power Delivers Thunderous Volume

Packing high-current output transistors and a beefy toroidal transformer, the Behringer EP4000 delivers up to 2,000W of peak power per channel into 2-ohm loads. Connect it to large-format speaker arrays and you'll have all the amplification you need to fill stadiums, arenas and festival grounds with powerful, room-filling sound. The EP4000 puts out 1,400W per channel into 4 ohms as well—ideal for powering full-range mains and monitors. And running in bridge mode, it delivers a monstrous 4,000W into 4 ohms, enough for massive subwoofer arrays.

Accelerated Transient Response Ensures Punchy, Articulate Sound

Behringer's proprietary ATR technology gives the EUROPOWER EP4000 exceptional sonic clarity and detail. By improving the amplifier's slew rate and damping factor, ATR results in precise, punchy bass, articulate mids and shimmering highs. Snare hits snap with authority, guitar tones bite and cymbals shimmer with realistic decay. Vocals and lead instruments shine through the mix. Even at extremely high volumes, your sound stays clean and free of distortion thanks to ATR.

Low-Frequency Filters Remove Unwanted Bass

Unruly sub-bass frequencies can muddy up a mix and strain speaker cones. The EUROPOWER EP4000 lets you filter out excessive low end with adjustable high-pass filters on each channel. Set the filters anywhere from 10Hz–400Hz to remove sub-sonic rumble and tighten up low end. It's a great way to optimize your rig for the room without compromising headroom and dynamics.

Output Power
  • 20Hz–20kHz @ 0.1% THD, both channels driven:
  • 8 ohms per channel - 550W
  • 4 ohms per channel - 950W
  • 2 ohms per channel - 1,250W
RMS @ 1% THD (sine wave), bridged mode:
  • 8 ohms - 1,750W
  • 4 ohms - 2.400W
Peak Power, both channels driven:
  • 8 ohms per channel - 750W
  • 4 ohms per channel - 1,400W
  • 2 ohms per channel - 2,000W
Peak Power, bridged mode:
  • 8 ohms - 2,800W
  • 4 ohms - 4,000W
  • Distortion: <0.02%
Frequency Response:
  • At 10dB below rated output Power-20Hz–20kHz
  • At -3dB points: 5Hz–50kHz
  • Damping Factor: >300 at 8Î
  • Noise: -100dB unweighted, 20Hz–20kHz
  • Voltage Gain: 40X (32dB)
  • Input sensitivity: 1.15V (+3.4dBu) VRMS at 8 ohms
  • Input impedance: 10 kohm unbalanced, 20 kohm balanced
  • Front: Power switch,gain control (channels 1 and 2)
  • Rear: DIP switches (10x)
  • Power: Green LED
  • Clip: Red LED, 1 per channel
  • Signal: Yellow LED, 1 per channel
  • Inputs: Balanced XLR and 1/4" TRS connectors
  • Outputs: Touch-proof binding posts and professional speaker connectors
  • Cooling: Continuously variable-speed fan, back-to-front airflow
  • Amplifier Protection: Full short-circuit, open circuit, thermal, and HF protection
  • Load Protection: Turn on/off muting, AC coupling
  • Output Circuit Type: Class H complementary linear output
Mains Voltage/Breaker:
  • 100–120V, 50/60Hz, 15 amps
  • 220–230V, 50/60Hz, 8 amps
  • Power Consumption: 2600W
  • Mains connector: Standard IEC receptacle
  • WxHxD: 19"x 3-1/2" x 15-4/5"
  • Weight: 37 lb.


  • 2 x 2,000 watts into 2 ohms; 2 x 1,400 watts into 4 ohms; 4,000 watts into 4 ohms (bridge mode)
  • Precise Power, Signal and Clip LEDs to monitor performance
  • XLR and 1/4" TRS input connectors for compatibility with any source
  • Professional speaker connectors and "touch-proof" binding posts support most speaker wiring systems
  • Selectable low-frequency filters (30Hz or 50Hz) remove distracting infra-sound frequencies
  • Independent limiters per channel offer reliable protection against overload and distortion
  • High-current toroidal transformer for ultrahigh transient response and absolute reliability
  • Ultrareliable Toshiba/Fairchild power transistors
  • Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
  • Back-to-front ventilation system, including air filter for reliable operation
  • "Built-like-a-tank," impact-resistant, all-steel 2U rackmount chassis
  • High-quality components and exceptionally rugged construction ensure long life
  • Conceived and designed by Behringer Germany